This is a list of published standards[Note 1] from the International Organization for Standardization (ISO) and other final products.[Note 2].
The standards are protected by copyright and most of them must be purchased. However, around 300 of the standards developed by the Joint Technical Committee 1 (JTC1) of ISO and IEC.
ISO 1 – ISO 99
• - ISO 1:2016 Geometric Product Specification (GPS). Normalized reference temperature for the specification of geometric and dimensional properties.
• - ISO 2"):1973 Textiles - Designation of the direction of twist in yarns and related products.
• - ISO 3") Preferred number series.
• - ISO 4:1997 Rules for the abbreviation of title words and titles of publications:.
• - ISO 5") Photography and graphic technology - Density measurements.
ISO 5-1:2009 Part 1: Geometry and functional notation.
ISO 5-2:2009 Part 2: Geometric conditions for transmittance density.
ISO 5-3:2009 Part 3: Spectral conditions.
ISO 5-4:2009 Part 4: Geometric conditions for reflection density.
• - ISO 6"):1993 Photography and graphic technology - Density measurements.
• - ISO 7") Pipe threads where pressure-tight joints are made on the threads:
ISO 7-1:1994 Part 1: Dimensions, tolerances and designation:
ISO 7-1:2007 Technical correction 1.
ISO 7-2: 2000 Part 2: Verification using limit gauges.
• - ISO 8"):2019 Presentation of periodical publications.
• - ISO 9:1995 Transcription of Cyrillic characters into Latin characters - Slavic and non-Slavic languages.
• - ISO 10 No information.
• - ISO 11:1987 Aircraft - Ground pressure test connections for pressure cabins.
• - ISO 12:1987 Aerospace - Pipelines - Identification.
• - ISO 13:1978 Gray iron pipes, special castings and gray iron parts for main pressure lines [Withdrawn without replacement].
• - ISO 14:1982 Straight-sided grooves for cylindrical shafts with internal centering - Dimensions, tolerances and verification.
Reverse bending test
Introduction
This is a list of published standards[Note 1] from the International Organization for Standardization (ISO) and other final products.[Note 2].
The standards are protected by copyright and most of them must be purchased. However, around 300 of the standards developed by the Joint Technical Committee 1 (JTC1) of ISO and IEC.
ISO 1 – ISO 99
• - ISO 1:2016 Geometric Product Specification (GPS). Normalized reference temperature for the specification of geometric and dimensional properties.
• - ISO 2"):1973 Textiles - Designation of the direction of twist in yarns and related products.
• - ISO 3") Preferred number series.
• - ISO 4:1997 Rules for the abbreviation of title words and titles of publications:.
• - ISO 5") Photography and graphic technology - Density measurements.
ISO 5-1:2009 Part 1: Geometry and functional notation.
ISO 5-2:2009 Part 2: Geometric conditions for transmittance density.
ISO 5-3:2009 Part 3: Spectral conditions.
ISO 5-4:2009 Part 4: Geometric conditions for reflection density.
• - ISO 6"):1993 Photography and graphic technology - Density measurements.
• - ISO 7") Pipe threads where pressure-tight joints are made on the threads:
ISO 7-1:1994 Part 1: Dimensions, tolerances and designation:
ISO 7-1:2007 Technical correction 1.
ISO 7-2: 2000 Part 2: Verification using limit gauges.
• - ISO 8"):2019 Presentation of periodical publications.
• - ISO 9:1995 Transcription of Cyrillic characters into Latin characters - Slavic and non-Slavic languages.
• - ISO 10 No information.
• - ISO 11:1987 Aircraft - Ground pressure test connections for pressure cabins.
• - ISO 15:2017 Bearings - Radial bearings - Limit dimensions, general drawing.
• - ISO 16:1975 Standard tuning frequency (Musical pitch "Pitch (music)") standard).
• - ISO 17:1973 Guide for the use of preferred numbers and preferred number series Documentation.
• - ISO 18:1981 List of contents of periodicals.
• - ISO 19 No information.
• - ISO 20 No information.
• - ISO 21:1985 Shipbuilding - Inland navigation - Cable hoists for anchor chains with stud links [Withdrawn without replacement] .
• - ISO 22:1991 Belt drives - Flat transmission belts and corresponding pulleys - Dimensions and tolerances.
• - ISO 23:1993 Cinematography - Use of 35 mm cinematographic film camera - Specifications.
• - ISO 24:1956 Cinematography - Use of the 35 mm cinematographic film projector for direct front projection - Specifications [Withdrawn: superseded by ISO 2939].
• - ISO 25:1994 Cinematography - Use of 16 mm cinematographic film camera - Specifications.
• - ISO 26:1993 Cinematography - Use of the 16 mm cinematographic film projector for direct front projection - Specifications.
• - ISO 27 No information.
• - ISO 28:1976 Cinematography - Use of 8 mm type R cinematographic film camera - Specifications.
• - ISO 29:1980 Cinematography - Use of Type R 8mm Silent Motion Picture Projector for Direct Front Projection - Specifications [Withdrawn without replacement].
• - ISO 30:1956 Bibliographic strip [Withdrawn without replacement].
• - ISO 31 Quantities and units [Withdrawn: replaced by ISO/IEC 80000]:
ISO 31-0: General principles.
ISO 31-1: Space and time (superseded by ISO/IEC 80000-3:2007).
ISO 31-2: Periodic and related phenomena (superseded by ISO/IEC 80000-3:2007).
ISO 31-3: Mechanical (superseded by ISO/IEC 80000-4:2006).
ISO 31-4: Heat (superseded by ISO/IEC 80000-5).
ISO 31-5: Electricity and magnetism (replaced by ISO/IEC 80000-6).
ISO 31-6: Electromagnetic light and related radiation (superseded by ISO/IEC 80000-7).
ISO 31-7: Acoustics (superseded by ISO/IEC 80000-8: 2007).
ISO 31-8: Physical chemistry and molecular physics (superseded by ISO/IEC 80000-9).
ISO 31-9: Atomic and nuclear physics (replaced by ISO/IEC 80000-10).
ISO 31-10: Nuclear reactions and ionizing radiation.
ISO 31-11: Mathematical signs and symbols for use in the physical sciences and technology (superseded by ISO 80000-2:2009).
ISO 31-12: Characteristic numbers (replaced by ISO/IEC 80000-11).
ISO 31-13: Solid state physics (superseded by ISO/IEC 80000-12).
• - ISO 32:1977 Gas cylinders for medical use - Marking for identification of contents.
• - ISO 33 No information.
• - ISO 34 Vulcanized rubber or thermoplastic. Determination of tear resistance:
ISO 34-1:2015 Part 1: Trouser, angle and half-moon test pieces.
ISO 34-2:2015 Part 2: Small test pieces (Delft).
• - ISO 35:2004 Natural rubber latex concentrate. Determination of mechanical stability.
• - ISO 36:2020 Rubber, vulcanized or thermoplastic - Determination of adhesion to textile fabrics.
• - ISO 37:2017 Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties.
• - ISO 38 No information.
• - ISO 39 No information.
• - ISO 40 No information.
• - ISO 41:1980 Shipbuilding - Inland ships - Covers for deck openings for pumps [Withdrawn without replacement].
• - ISO 42:1957 Shipbuilding - Inland vessels - Mushroom ventilation headers [Withdrawn: Superseded by ISO 3372, now withdrawn without replacement].
• - ISO 43:2016 Aircraft - Lifting platforms.
• - ISO 44:1975 Aerospace - Lever-operated two-position on/off switches - Directions of operation.
• - ISO 45:1990 Aircraft - Pressure refueling connections.
• - ISO 46:1973 Aircraft - Fuel nozzle grounding plugs and sockets.
• - ISO 47:1957 Aircraft - Toilet connections [Withdrawn: replaced by ISO 450, later ISO 17775].
• - ISO 48 Vulcanized rubber or thermoplastic - Determination of hardness:
ISO 48-1:2018 Part 1: Introduction and guidance.
ISO 48-2:2018 Part 2: Hardness between 10 IRHD and 100 IRHD.
ISO 48-3:2018 Part 3: Dead load hardness using the very low rubber hardness (VLRH) scale.
ISO 48-4:2018 Part 4: Indentation hardness by durometer method (Shore hardness).
ISO 48-5:2018 Part 5: Indentation hardness by IRHD pocket meter method.
ISO 48-6:2018 Part 6: Apparent hardness of rubber-coated rollers by IRHD method.
ISO 48-7: 2018 Part 7: Apparent hardness of rubber-coated rollers by the Shore durometer method.
ISO 48-8:2018 Part 8: Apparent hardness of rubber-coated rollers by the Pusey and Jones method.
ISO 48-9:2018 Part 9: Calibration and verification of hardness testers.
• - ISO 49:1994 Threaded malleable cast iron fittings according to ISO 7-1.
• - ISO 50:1977 Metal pipes - Bolted steel sockets according to ISO 7 [Withdrawn without replacement].
• - ISO 51 No information.
• - ISO 52 No information.
• - ISO 53:1998 Spur gears for general and heavy engineering - Standard basic rack tooth profile.
• - ISO 54:1996 Cylindrical gears for general engineering and heavy engineering - Modules.
• - ISO 55:1977 Seedlac - Specification [Withdrawn without replacement].
• - ISO 56:1979 Shellac - Specification [Withdrawn without replacement]:
ISO 56-1:1979 Handmade shellac - Specification [Withdrawn without replacement].
ISO 56-2:1979 Machine-made shellac - Specification [Withdrawn without replacement].
• - ISO 57:1975 Whitewashed lacquer - Specification [Withdrawn without replacement].
• - ISO 58:1958 Paper Substances [Withdrawn without replacement].
• - ISO 59:1976 Plastics - Determination of matter soluble in acetone [Withdrawn without replacement].
• - ISO 60:1977 Plastics: Determination of the apparent density of material that can be poured from a specified funnel.
• - ISO 61:1976 Plastics: Determination of the apparent density of molding material that cannot be poured from a specified funnel.
• - ISO 62:2008 Plastics - Determination of water absorption.
• - ISO 63:1975 Flat transmission belts - Lengths [Withdrawn: superseded by ISO 22].
• - ISO 64:1974 Carbon steel tubes - Lengths [Withdrawn: Superseded by ISO 4200:1991].
• - ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1.
• - ISO 66:1958 Paper vocabulary - First series of terms [Deleted: replaced by ISO 4046].
• - ISO 67:1981 Muscovite mica blocks, thins and films - Classification by size [Withdrawn without replacement].
• - ISO 68 General purpose rocks - Basic profile:
ISO 68-1"):1998 Part 1: Metric thread.
ISO 68-2"):1998 Part 2: Screw threads in inches.
• - ISO 69:1998 Cinematography - 16 mm film and magnetic film - Cutting and perforation dimensions.
• - ISO 70:1981 Cinematography - Recording 35 mm negative photographic sound on 35 mm cinematographic film - Maximum position and width dimensions.
• - ISO 71:2014 Cinematography: recording 16 mm negative photographic sound on 16 mm, 35/16 mm and 35/32 mm cinematographic films: positions and dimensions.
• - ISO 72 No information.
• - ISO 73:1958 Cinematography - Image area produced by the camera aperture in 35 mm cinematographic film - Positions and dimensions [Withdrawn: superseded by ISO 2906 and ISO 2907].
• - ISO 74:1976 Cinematography: image area produced by the camera aperture and the maximum projectable image area on 8 mm type R cinematographic film: positions and dimensions.
• - ISO 75 Plastics - Determination of deflection temperature under load:
ISO 75-1:2020 Part 1: General test method.
ISO 75-2:2013 Part 2: Plastics and ebonite.
ISO 75-3:2004 Part 3: High-strength thermosetting laminates and long fiber reinforced plastics.
• - ISO 76:2006 Bearings - Static load classifications.
• - ISO 77 No information.
• - ISO 78 Chemistry - Designs for standards:
ISO 78-1 No information.
ISO 78-2:1999 Part 2: Methods of chemical analysis.
ISO 78-3:1983 Part 3: Standard for molecular absorption spectrometry [Withdrawn without replacement].
ISO 78-4:1983 Part 4: Standard for atomic absorption spectrometric analysis [Withdrawn without replacement].
• - ISO / TR 79:2015 Reference materials: examples of reference materials for qualitative properties.
• - ISO 80:1968 Rockwell hardness test (B and C scales) for steel [Withdrawn: superseded by ISO 6508].
• - ISO 81:1967 Vickers hardness test for steel (5 to 100 kgf load) [Withdrawn: superseded by ISO 6507-1].
• - ISO 82:1974 Steel - Tensile test [Withdrawn: superseded by ISO 6892-1].
• - ISO 83:1976 Steel - Charpy (U-notch) impact test [Withdrawn: superseded by ISO 148-1].
• - ISO 84:1959 Izod impact test for steel [withdrawn without replacement].
• - ISO 85:1959 Bending test for steel [Withdrawn: replaced by ISO 7438].
• - ISO 86:1974 Steel - Tensile test of sheets and strips less than 3 mm and not less than 0.5 mm thick [Withdrawn: superseded by ISO 6892-1].
• - ISO 87:1959 Simple bending test of steel sheets and strips less than 3 mm thick [Withdrawn: superseded by ISO 7438].
• - ISO 88:1959 Reverse bending test of steel sheets and strips less than 3 mm thick [Withdrawn: replaced by ISO 7799].
• - ISO 89:1974 Steel - Wire tensile test [Withdrawn: superseded by ISO 6892-1].
• - ISO 90 Light gauge metal containers - Definitions and determination of dimensions and capacities:
ISO 90-1:1997 Part 1: Open cans.
ISO 90-2:1997 Part 2: General purpose containers.
ISO 90-3:2000 Part 3: Aerosol cans.
• - ISO 91:2017 Petroleum and related products - Temperature and pressure volume correction factors (petroleum measurement tables) and standard reference conditions.
• - ISO 92: 1976 Textile machinery and accessories - Spinning machinery - Definition of side (left or right).
• - ISO 93 Textile machinery and accessories - Cylindrical chip cans:
ISO 93-1:2006 Part 1: Main dimensions.
ISO 93-2:2006 Part 2: spring bottoms.
ISO 93-3:1981 Part 3: Packaging of tape cans (press cans) [Withdrawn without replacement].
• - ISO 94:1982 Textile machinery and accessories - Spindle gauges for ring spinning and duplicating frames.
• - ISO 95 No information.
• - ISO 96 Textile machinery and accessories - Rings and sliders for ring spinning and twisting structures:
ISO 96-1:2016 Part 1: T and SF flange rings and their guides.
ISO 96-2:2009 Part 2: HZ and J rings and their travelers.
• - ISO 97:1975 Textile machinery and accessories - Spinning, folding and twisting rings for ear-shaped travelers [Withdrawn: superseded by ISO 96-2].
• - ISO 98:2001 Textile machinery and accessories - Spinning and preparatory machinery - Main dimensions of coverings for upper rollers.
• - ISO 99: 1975 Pulleys for flat transmission belts - Diameters [Withdrawn: superseded by ISO 22].
ISO 100 – ISO 199
• - ISO 128") Technical Product Documentation (TPD). General principles of representation.[Note 3]
ISO 128-1:2020 Part 1: Introduction and fundamental requirements.
ISO 128-2:2020 Part 2: Basic conventions for lines.
ISO 128-3:2020 Part 3: Views, sections "Section (geometry)") and cuts.
ISO 128-15:2013 Part 15: Presentation of shipbuilding plans.
ISO 128-20:1996 Part 20: Basic conventions for lines [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-21:1997 Part 21: Line preparation using CAD systems [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-22:1999 Part 22: Basic conventions and uses for dimension lines and reference lines [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-23:1999 Part 23: Lines on construction drawings [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-24:2014 Part 24: Lines on mechanical engineering drawings [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-25:1999 Part 25: Lines on shipbuilding drawings [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-30:2001 Part 30: Basic conventions for views [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-33:2018 Part 33: Representation of views, sections and sections on construction drawings [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-34:2001 Part 34: Views on mechanical engineering drawings [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-40:2001 Part 40: Basic conventions for cuts and sections [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-43:2015 Part 43: Projection methods on building drawings.
ISO 128-44:2001 Part 44: Sections on mechanical engineering drawings [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-50:2001 Part 50: Basic conventions for representing areas on cuts [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-71:2010 Part 71: Simplified representation for mechanical engineering drawings.
ISO 128-100:2020 Part 100: Index.
ISO 200 – ISO 299
• - ISO 216:2003 Letter paper and certain kinds of printed material - Trimmed sizes - Series A and B and indication of machine direction.
• - ISO 261:1998 ISO general purpose metric thread - General drawing.
• - ISO 262:1998 ISO general purpose metric thread - Selected sizes for screws, bolts and nuts.
ISO 600 – ISO 699
• - ISO 639 Codes for the representation of language names:
ISO 639-1:2002 Part 1: Alpha-2 codes (Two-letter codes for some languages).
ISO 639-2:1998 Part 2: Alpha-3 codes (Three-letter codes for languages and language groups).
ISO 639-3:2007 Part 3: Alpha-3 codes for a comprehensive treatment of languages (It has more codes than part 2 but does not include the language groups that are in part 2).
ISO 639-4"):2010 Part 4: General principles for the encoding of the representation of names of languages and related entities, and guidelines for their application.
ISO 639-5:2008 Part 5: Alpha-3 codes for language families and language groups.
ISO 639-6:2008 Part 6: Alpha-4 codes for complete coverage of linguistic variants [Withdrawn, not replaced].
• - ISO 646:1991 7-bit character set for information exchange.
• - ISO 690:2013 Information and documentation. Guidelines for writing bibliographic references and citations of information resources.
ISO 700 – ISO 799
• - ISO 724:1993 ISO general purpose metric thread - Basic dimensions.
• - ISO 732:2000 Photography - 120 and 220 size films - Dimensions.
ISO 800 – ISO 899
• - ISO 838:1974 Paper - Holes for general filing purposes - Specifications (or Standard for paper punches).
ISO 900 – ISO 999
ISO 962:1974 Materialization of the 7-bit character set and its 7-bit and 8-bit extensions, on 12.7 mm (0.5 inch) wide 9-track magnetic tape.
• - ISO 12:1987 Aerospace - Pipelines - Identification.
• - ISO 13:1978 Gray iron pipes, special castings and gray iron parts for main pressure lines [Withdrawn without replacement].
• - ISO 14:1982 Straight-sided grooves for cylindrical shafts with internal centering - Dimensions, tolerances and verification.
• - ISO 15:2017 Bearings - Radial bearings - Limit dimensions, general drawing.
• - ISO 16:1975 Standard tuning frequency (Musical pitch "Pitch (music)") standard).
• - ISO 17:1973 Guide for the use of preferred numbers and preferred number series Documentation.
• - ISO 18:1981 List of contents of periodicals.
• - ISO 19 No information.
• - ISO 20 No information.
• - ISO 21:1985 Shipbuilding - Inland navigation - Cable hoists for anchor chains with stud links [Withdrawn without replacement] .
• - ISO 22:1991 Belt drives - Flat transmission belts and corresponding pulleys - Dimensions and tolerances.
• - ISO 23:1993 Cinematography - Use of 35 mm cinematographic film camera - Specifications.
• - ISO 24:1956 Cinematography - Use of the 35 mm cinematographic film projector for direct front projection - Specifications [Withdrawn: superseded by ISO 2939].
• - ISO 25:1994 Cinematography - Use of 16 mm cinematographic film camera - Specifications.
• - ISO 26:1993 Cinematography - Use of the 16 mm cinematographic film projector for direct front projection - Specifications.
• - ISO 27 No information.
• - ISO 28:1976 Cinematography - Use of 8 mm type R cinematographic film camera - Specifications.
• - ISO 29:1980 Cinematography - Use of Type R 8mm Silent Motion Picture Projector for Direct Front Projection - Specifications [Withdrawn without replacement].
• - ISO 30:1956 Bibliographic strip [Withdrawn without replacement].
• - ISO 31 Quantities and units [Withdrawn: replaced by ISO/IEC 80000]:
ISO 31-0: General principles.
ISO 31-1: Space and time (superseded by ISO/IEC 80000-3:2007).
ISO 31-2: Periodic and related phenomena (superseded by ISO/IEC 80000-3:2007).
ISO 31-3: Mechanical (superseded by ISO/IEC 80000-4:2006).
ISO 31-4: Heat (superseded by ISO/IEC 80000-5).
ISO 31-5: Electricity and magnetism (replaced by ISO/IEC 80000-6).
ISO 31-6: Electromagnetic light and related radiation (superseded by ISO/IEC 80000-7).
ISO 31-7: Acoustics (superseded by ISO/IEC 80000-8: 2007).
ISO 31-8: Physical chemistry and molecular physics (superseded by ISO/IEC 80000-9).
ISO 31-9: Atomic and nuclear physics (replaced by ISO/IEC 80000-10).
ISO 31-10: Nuclear reactions and ionizing radiation.
ISO 31-11: Mathematical signs and symbols for use in the physical sciences and technology (superseded by ISO 80000-2:2009).
ISO 31-12: Characteristic numbers (replaced by ISO/IEC 80000-11).
ISO 31-13: Solid state physics (superseded by ISO/IEC 80000-12).
• - ISO 32:1977 Gas cylinders for medical use - Marking for identification of contents.
• - ISO 33 No information.
• - ISO 34 Vulcanized rubber or thermoplastic. Determination of tear resistance:
ISO 34-1:2015 Part 1: Trouser, angle and half-moon test pieces.
ISO 34-2:2015 Part 2: Small test pieces (Delft).
• - ISO 35:2004 Natural rubber latex concentrate. Determination of mechanical stability.
• - ISO 36:2020 Rubber, vulcanized or thermoplastic - Determination of adhesion to textile fabrics.
• - ISO 37:2017 Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties.
• - ISO 38 No information.
• - ISO 39 No information.
• - ISO 40 No information.
• - ISO 41:1980 Shipbuilding - Inland ships - Covers for deck openings for pumps [Withdrawn without replacement].
• - ISO 42:1957 Shipbuilding - Inland vessels - Mushroom ventilation headers [Withdrawn: Superseded by ISO 3372, now withdrawn without replacement].
• - ISO 43:2016 Aircraft - Lifting platforms.
• - ISO 44:1975 Aerospace - Lever-operated two-position on/off switches - Directions of operation.
• - ISO 45:1990 Aircraft - Pressure refueling connections.
• - ISO 46:1973 Aircraft - Fuel nozzle grounding plugs and sockets.
• - ISO 47:1957 Aircraft - Toilet connections [Withdrawn: replaced by ISO 450, later ISO 17775].
• - ISO 48 Vulcanized rubber or thermoplastic - Determination of hardness:
ISO 48-1:2018 Part 1: Introduction and guidance.
ISO 48-2:2018 Part 2: Hardness between 10 IRHD and 100 IRHD.
ISO 48-3:2018 Part 3: Dead load hardness using the very low rubber hardness (VLRH) scale.
ISO 48-4:2018 Part 4: Indentation hardness by durometer method (Shore hardness).
ISO 48-5:2018 Part 5: Indentation hardness by IRHD pocket meter method.
ISO 48-6:2018 Part 6: Apparent hardness of rubber-coated rollers by IRHD method.
ISO 48-7: 2018 Part 7: Apparent hardness of rubber-coated rollers by the Shore durometer method.
ISO 48-8:2018 Part 8: Apparent hardness of rubber-coated rollers by the Pusey and Jones method.
ISO 48-9:2018 Part 9: Calibration and verification of hardness testers.
• - ISO 49:1994 Threaded malleable cast iron fittings according to ISO 7-1.
• - ISO 50:1977 Metal pipes - Bolted steel sockets according to ISO 7 [Withdrawn without replacement].
• - ISO 51 No information.
• - ISO 52 No information.
• - ISO 53:1998 Spur gears for general and heavy engineering - Standard basic rack tooth profile.
• - ISO 54:1996 Cylindrical gears for general engineering and heavy engineering - Modules.
• - ISO 55:1977 Seedlac - Specification [Withdrawn without replacement].
• - ISO 56:1979 Shellac - Specification [Withdrawn without replacement]:
ISO 56-1:1979 Handmade shellac - Specification [Withdrawn without replacement].
ISO 56-2:1979 Machine-made shellac - Specification [Withdrawn without replacement].
• - ISO 57:1975 Whitewashed lacquer - Specification [Withdrawn without replacement].
• - ISO 58:1958 Paper Substances [Withdrawn without replacement].
• - ISO 59:1976 Plastics - Determination of matter soluble in acetone [Withdrawn without replacement].
• - ISO 60:1977 Plastics: Determination of the apparent density of material that can be poured from a specified funnel.
• - ISO 61:1976 Plastics: Determination of the apparent density of molding material that cannot be poured from a specified funnel.
• - ISO 62:2008 Plastics - Determination of water absorption.
• - ISO 63:1975 Flat transmission belts - Lengths [Withdrawn: superseded by ISO 22].
• - ISO 64:1974 Carbon steel tubes - Lengths [Withdrawn: Superseded by ISO 4200:1991].
• - ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1.
• - ISO 66:1958 Paper vocabulary - First series of terms [Deleted: replaced by ISO 4046].
• - ISO 67:1981 Muscovite mica blocks, thins and films - Classification by size [Withdrawn without replacement].
• - ISO 68 General purpose rocks - Basic profile:
ISO 68-1"):1998 Part 1: Metric thread.
ISO 68-2"):1998 Part 2: Screw threads in inches.
• - ISO 69:1998 Cinematography - 16 mm film and magnetic film - Cutting and perforation dimensions.
• - ISO 70:1981 Cinematography - Recording 35 mm negative photographic sound on 35 mm cinematographic film - Maximum position and width dimensions.
• - ISO 71:2014 Cinematography: recording 16 mm negative photographic sound on 16 mm, 35/16 mm and 35/32 mm cinematographic films: positions and dimensions.
• - ISO 72 No information.
• - ISO 73:1958 Cinematography - Image area produced by the camera aperture in 35 mm cinematographic film - Positions and dimensions [Withdrawn: superseded by ISO 2906 and ISO 2907].
• - ISO 74:1976 Cinematography: image area produced by the camera aperture and the maximum projectable image area on 8 mm type R cinematographic film: positions and dimensions.
• - ISO 75 Plastics - Determination of deflection temperature under load:
ISO 75-1:2020 Part 1: General test method.
ISO 75-2:2013 Part 2: Plastics and ebonite.
ISO 75-3:2004 Part 3: High-strength thermosetting laminates and long fiber reinforced plastics.
• - ISO 76:2006 Bearings - Static load classifications.
• - ISO 77 No information.
• - ISO 78 Chemistry - Designs for standards:
ISO 78-1 No information.
ISO 78-2:1999 Part 2: Methods of chemical analysis.
ISO 78-3:1983 Part 3: Standard for molecular absorption spectrometry [Withdrawn without replacement].
ISO 78-4:1983 Part 4: Standard for atomic absorption spectrometric analysis [Withdrawn without replacement].
• - ISO / TR 79:2015 Reference materials: examples of reference materials for qualitative properties.
• - ISO 80:1968 Rockwell hardness test (B and C scales) for steel [Withdrawn: superseded by ISO 6508].
• - ISO 81:1967 Vickers hardness test for steel (5 to 100 kgf load) [Withdrawn: superseded by ISO 6507-1].
• - ISO 82:1974 Steel - Tensile test [Withdrawn: superseded by ISO 6892-1].
• - ISO 83:1976 Steel - Charpy (U-notch) impact test [Withdrawn: superseded by ISO 148-1].
• - ISO 84:1959 Izod impact test for steel [withdrawn without replacement].
• - ISO 85:1959 Bending test for steel [Withdrawn: replaced by ISO 7438].
• - ISO 86:1974 Steel - Tensile test of sheets and strips less than 3 mm and not less than 0.5 mm thick [Withdrawn: superseded by ISO 6892-1].
• - ISO 87:1959 Simple bending test of steel sheets and strips less than 3 mm thick [Withdrawn: superseded by ISO 7438].
• - ISO 88:1959 Reverse bending test of steel sheets and strips less than 3 mm thick [Withdrawn: replaced by ISO 7799].
• - ISO 89:1974 Steel - Wire tensile test [Withdrawn: superseded by ISO 6892-1].
• - ISO 90 Light gauge metal containers - Definitions and determination of dimensions and capacities:
ISO 90-1:1997 Part 1: Open cans.
ISO 90-2:1997 Part 2: General purpose containers.
ISO 90-3:2000 Part 3: Aerosol cans.
• - ISO 91:2017 Petroleum and related products - Temperature and pressure volume correction factors (petroleum measurement tables) and standard reference conditions.
• - ISO 92: 1976 Textile machinery and accessories - Spinning machinery - Definition of side (left or right).
• - ISO 93 Textile machinery and accessories - Cylindrical chip cans:
ISO 93-1:2006 Part 1: Main dimensions.
ISO 93-2:2006 Part 2: spring bottoms.
ISO 93-3:1981 Part 3: Packaging of tape cans (press cans) [Withdrawn without replacement].
• - ISO 94:1982 Textile machinery and accessories - Spindle gauges for ring spinning and duplicating frames.
• - ISO 95 No information.
• - ISO 96 Textile machinery and accessories - Rings and sliders for ring spinning and twisting structures:
ISO 96-1:2016 Part 1: T and SF flange rings and their guides.
ISO 96-2:2009 Part 2: HZ and J rings and their travelers.
• - ISO 97:1975 Textile machinery and accessories - Spinning, folding and twisting rings for ear-shaped travelers [Withdrawn: superseded by ISO 96-2].
• - ISO 98:2001 Textile machinery and accessories - Spinning and preparatory machinery - Main dimensions of coverings for upper rollers.
• - ISO 99: 1975 Pulleys for flat transmission belts - Diameters [Withdrawn: superseded by ISO 22].
ISO 100 – ISO 199
• - ISO 128") Technical Product Documentation (TPD). General principles of representation.[Note 3]
ISO 128-1:2020 Part 1: Introduction and fundamental requirements.
ISO 128-2:2020 Part 2: Basic conventions for lines.
ISO 128-3:2020 Part 3: Views, sections "Section (geometry)") and cuts.
ISO 128-15:2013 Part 15: Presentation of shipbuilding plans.
ISO 128-20:1996 Part 20: Basic conventions for lines [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-21:1997 Part 21: Line preparation using CAD systems [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-22:1999 Part 22: Basic conventions and uses for dimension lines and reference lines [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-23:1999 Part 23: Lines on construction drawings [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-24:2014 Part 24: Lines on mechanical engineering drawings [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-25:1999 Part 25: Lines on shipbuilding drawings [Withdrawn: superseded by ISO 128-2:2020].
ISO 128-30:2001 Part 30: Basic conventions for views [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-33:2018 Part 33: Representation of views, sections and sections on construction drawings [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-34:2001 Part 34: Views on mechanical engineering drawings [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-40:2001 Part 40: Basic conventions for cuts and sections [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-43:2015 Part 43: Projection methods on building drawings.
ISO 128-44:2001 Part 44: Sections on mechanical engineering drawings [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-50:2001 Part 50: Basic conventions for representing areas on cuts [Withdrawn: superseded by ISO 128-3:2020].
ISO 128-71:2010 Part 71: Simplified representation for mechanical engineering drawings.
ISO 128-100:2020 Part 100: Index.
ISO 200 – ISO 299
• - ISO 216:2003 Letter paper and certain kinds of printed material - Trimmed sizes - Series A and B and indication of machine direction.
• - ISO 261:1998 ISO general purpose metric thread - General drawing.
• - ISO 262:1998 ISO general purpose metric thread - Selected sizes for screws, bolts and nuts.
ISO 600 – ISO 699
• - ISO 639 Codes for the representation of language names:
ISO 639-1:2002 Part 1: Alpha-2 codes (Two-letter codes for some languages).
ISO 639-2:1998 Part 2: Alpha-3 codes (Three-letter codes for languages and language groups).
ISO 639-3:2007 Part 3: Alpha-3 codes for a comprehensive treatment of languages (It has more codes than part 2 but does not include the language groups that are in part 2).
ISO 639-4"):2010 Part 4: General principles for the encoding of the representation of names of languages and related entities, and guidelines for their application.
ISO 639-5:2008 Part 5: Alpha-3 codes for language families and language groups.
ISO 639-6:2008 Part 6: Alpha-4 codes for complete coverage of linguistic variants [Withdrawn, not replaced].
• - ISO 646:1991 7-bit character set for information exchange.
• - ISO 690:2013 Information and documentation. Guidelines for writing bibliographic references and citations of information resources.
ISO 700 – ISO 799
• - ISO 724:1993 ISO general purpose metric thread - Basic dimensions.
• - ISO 732:2000 Photography - 120 and 220 size films - Dimensions.
ISO 800 – ISO 899
• - ISO 838:1974 Paper - Holes for general filing purposes - Specifications (or Standard for paper punches).
ISO 900 – ISO 999
ISO 962:1974 Materialization of the 7-bit character set and its 7-bit and 8-bit extensions, on 12.7 mm (0.5 inch) wide 9-track magnetic tape.